.تعمیـــرکاران کیان ست (kiansat.kim)تابع قوانین -جمهموری-اسلامی ایران میباشد و ارسال هر گونه مطلب سیاسی،مذهبی،غیراخلاقی و خرید و فروش متعلقات ماه-واره و دیگر موارد مجرمانه ممنوع میباشد وبا کاربران خاطی به شدت برخورد میگردد انجمن فقط تعمیرات لوازم الکترونیک میباشد...













سلام مهمان گرامی؛
به کیان ست خوش آمدید برای مشاهده انجمن با امکانات کامل می بايست از طريق این لینک عضو شوید.

http://teranzit.pw/uploads/14469017281.png
پیام خصوصی به مدیریت کل سایت ........... صفحه توضیحات و شرایط گروه ویژه ........... ...........
ارتباط تلگرامی با مدیریت سایت ................. ایدی تلگرام suportripair@ .................
نمایش نتایج: از شماره 1 تا 1 , از مجموع 1

موضوع: کد ها و خطاهای شارپ AR 350

  1. #1


    تاریخ عضویت
    Feb 2017
    محل سکونت
    پایتخت خوشنویسی ایران(گژوین.بناشده درزمان ساسانیان)
    علایق
    کوهنوردی.شنا
    شغل و حرفه
    تکنسین الکترونیک
    نوشته ها
    592
    تشکر ها
    1,076
    2,165 سپاس از547 پست

    پیش فرض کد ها و خطاهای شارپ AR 350

    TROUBLE CODES

    Trouble codes
    Contents
    Remark
    Trouble detection
    F1 03 Console finisher paddle motor trouble With Console Finisher installed PCU
    06 Console finisher slide motor trouble With Console Finisher installed PCU
    10 Console finisher stapler motor trouble With Console Finisher installed PCU
    11 Console finisher bundle exit motor trouble With Console Finisher installed PCU
    15 Console finisher lift motor trouble With Console Finisher installed PCU
    19 Console finisher alignment motor trouble FRONT With Console Finisher installed PCU
    20 Console finisher alignment motor trouble With Console Finisher installed PCU
    30 Console finisher communication trouble With Console Finisher installed PCU
    31 Console finisher fold sensor trouble With Console Finisher installed PCU
    32 Console finisher punch unit communication trouble With Console Finisher installed PCU
    33 Console finisher punch side register motor trouble With Console Finisher installed PCU
    34 Console finisher punch motor trouble With Console Finisher installed PCU
    35 Console finisher punch side register sensor trouble With Console Finisher installed PCU
    36 Console finisher punch timing sensor trouble With Console Finisher installed PCU
    37 Console finisher backup RAM trouble With Console Finisher installed PCU
    38 Console finisher punch backup RAM trouble With Console Finisher installed PCU
    81 Console finisher transport motor trouble With Console Finisher installed PCU
    F2 00 شارپ ar450-ar350 تونر concentration sensor open PCU
    02 شارپ ar450-ar350 تونر supply abnormality PCU
    04 Improper cartridge
    (Destination error, life cycle error)
    PCU
    05 CRUM error PCU
    39 Process thermistor breakdown PCU
    F3 12 Tray 1 lift-p trouble PCU
    22 Tray 2 lift-up trouble (Multi-purpose tray) Multi-purpose tray PCU
    1.
    Trouble codes list
    Trouble codes
    Contents
    Remark
    Trouble detection
    F6 00 FAX board communication trouble When the Fax board is installed ICU
    01 FAX expansion Flash Rom abnormality When the Fax board is installed ICU
    04 FAX MODEM operation abnormality When the Fax board is installed FAX
    F7 01 FAX board EEPROM read/write error When the Fax board is installed FAX
    H2 00 Thermistor open (HL1) PCU
    01 Thermistor open (HL2) PCU
    H3 00 Heat roller high temperature detection (HL1) PCU
    01 Heat roller high temperature detection (HL2) PCU
    H4 00 Heat roller low temperature detection (HL1) PCU
    01 Heat roller low temperature detection (HL2) PCU
    H5 01 5-time continuous POD1 not-reaching JAM detection PCU
    L1 00 Scanner feed trouble When the scanner is installed SCANNER
    L3 00 Scanner return trouble When the scanner is installed SCANNER
    L4 01 main motor lock detection PCU
    02 Drum motor lock detection PCU
    L6 10 Polygon motor lock detection PCU
    L8 01 No full-wave signal PCU
    02 Full-wave signal width abnormality PCU
    U6 00 Desk/LCC communication trouble With Paper feed desk installed PCU
    01 Desk/LCC1CS lift-up trouble
    (Multi-purpose tray)
    With Paper feed desk installed PCU
    02 Desk2 CS lift-up trouble/LCC1 lift-up trouble With Paper feed desk installed PCU
    03 Desk3 CS lift-up trouble/LCC2 lift-up trouble With Paper feed desk installed PCU
    10 Desk/LCC transport motor trouble With Paper feed desk installed PCU
    EE EL Auto developer adjustment trouble (Over-شارپ ar450-ar350 تونر) Only during
    DIAG
    PCU
    EU Auto developer adjustment trouble (Under-شارپ ar450-ar350 تونر) Only during
    DIAG
    PCU
    F9 02 Centro port check error Controller
    03 NIC port check error Controller
    U1 01 FAX Battery abnormality With FAX board installed Controller
    02 RTC read abnormality (common with FAX, on ICU PWB) When the Fax board is installed ICU
    Trouble codes
    Contents
    Remark
    Trouble detection
    U2 00 EEPROM read/write error ( Controller ) Controller
    11 Counter check sum error ( Controller EEPROM ) Controller
    12 Adjustment value check sum error (Controller EEPROM) Controller
    80 Scanner section EEPROM read/write error When the scanner is installed SCANNER
    81 Scanner section memory sum check error When the scanner is installed SCANNER
    90 PCU section EEPROM read/ write error PCU
    91 PCU section memory sum check error PCU
    U7 00 PC/MODEM communication error Controller
    PF
    --
    RIC copy inhibit command reception Controller
    CH
    --
    Door open (CH ON) PCU
    00 No developer cartridge PCU
    01 No شارپ ar450-ar350 تونر cartridge PCU
    --
    --
    Auditor not ready Controller
    PC
    --
    Personal counter not installed Controller
    MAIN SUB
    C1 00 Content MC trouble
    Detail Main charger output abnormality
    ( Output open )
    Trouble signal is outputted from the high voltage transformer.
    Cause The main charger is not installed properly.
    The main charger is not assembled properly. Disconnection of connector of high voltage transformer.
    High voltage harness disconnection or breakage.
    Check and remedy Use the diag mode or DIAG to check the main charger output.
    Check for disconnection of the main charger.
    Replace the high voltage unit.
    E6 10 Content CIS shading trouble (Black correction)
    Details The CIS black scan level is abnormal when the lamp is off.
    Cause Abnormal harness installation to CIS unit
    CIS unit abnormality
    Scanner PWB abnormality
    Check &
    Remedy
    Check CIS unit harness.
    Check CIS unit.
    Check scanner PWB.

    1. 2.
    2. Details of trouble codes



    MAIN SUB
    E6 11 Content CSI shading trouble (White correction)
    Details The CIS white reference plate scan level is abnormal when the lamp is on.
    Cause Abnormal harness installation to CIS unit Dirt on the white reference plate.
    CIS lighting error
    CIS unit installation trouble
    CIS unit abnormality
    Scanner PWB abnormality
    Check &
    Remedy
    Clean the white reference plate.
    Check CIS light quantity (SIM 5-3) and lighting.
    Check CIS unit harness.
    Check scanner PWB.
    14 Content CIS communication trouble
    Details Communication trouble (clock sync) between scanner PWB and CIS-ASIC
    Cause Abnormal harness installation to CIS unit
    CIS unit abnormality
    Scanner PWB abnormality
    Check &
    Remedy
    Check CIS unit harness.
    Check CIS unit.
    Check scanner PWB.
    E7 02 Content Laser trouble
    Detail BD signal from LSU is kept OFF, or ON.
    Cause The connector of LSU or the harness in LSU is disconnected or broken.
    The polygon motor does not rotate normally. The laser home position sensor in LSU is shifted.
    The proper voltage is not supplied to the power line for laser.
    Laser emitting diode trouble
    PCU PWB trouble
    Controller PWB trouble
    Check and remedy Check for disconnection of the LSU connector.
    Use DIAG (SIM 61-1) to check LSU operation.
    Check that the polygon motor rotates normally or not.
    Check light emission of laser emitting diode.
    Replace the LSU unit.
    Replace the PCU PWB.
    Replace the Controller PWB.
    03 Content HDD trouble
    Detail HDD does not operate properly in the machine with HDD installed.
    Cause HDD is not installed properly to the Controller
    PWB.
    HDD does not operate properly in the Controller PWB.
    Controller PWB trouble
    Check and remedy Check installation of HDD to the Controller
    PWB.
    Check connection of the harness of HDD to the Controller PWB.
    Use DIAG (SIM 62-2, -3) to check read/write of HDD.
    Replace HDD.
    Replace Controller PWB.
    MAIN SUB
    E7 06 Content
    Decode error trouble
    Detail A decode error occurs during making of an image.
    Cause Data error during input from PCI to PM.
    PM trouble
    Data error during image compression/ transfer.
    Controller PWB abnormality
    Check and remedy Check insertion of the PWB. (PCI bus) If the error occurred in a FAX job, check installation of the FAX PWB.
    For the other cases, check the Controller PWB.
    Replace the Controller PWB.
    10 Content Shading trouble (Black correction)
    Details CCD black scan level abnormality when the copy lamp is off.
    Cause Abnormal installation of flat cable to CCD unit.
    CCD unit abnormality
    Scanner PWB abnormality
    Check &
    Remedy
    Check installation of CCD unit flat cable.
    Check CCD unit.
    Check scanner PWB.
    11 Content Shading trouble (White correction)
    Details CCD white reference plate scan level abnormality when the copy lamp is ON.
    Cause Abnormal installation of flat cable to CCD unit.
    Dirt on mirror, lens, white reference plate
    Copy lamp lighting abnormality
    Abnormal installation of CCD unit
    CCD unit abnormality
    Scanner PWB abnormality
    Check &
    Remedy
    Clean mirror, lens, and white reference plate. Check copy lamp light quantity (SIM 5-3) and lighting.
    Check CCD unit.
    Check scanner PWB.
    14 Content CCD communication trouble
    Details Communication trouble (clock sync) between scanner PWB and CCD-ASIC
    Cause Abnormal installation of harness to CCD unit
    CCD unit abnormality
    Scanner PWB abnormality
    Check &
    Remedy
    Check CCD unit harness.
    Check CCD unit.
    Check scanner PWB.
    50 Content LSU connection trouble
    Detail An LSU which does not conform to the machine is installed.
    Cause PCU PWB trouble LSU trouble
    Check and remedy Check LSU PWB. Check PCU PWB.
    Check connection of the connector and the harness between PCU and LSU.
    MAIN
    SUB MAIN SUB
    E7 80 Content Communication trouble (ICU detection) between ICU and scanner F1 19 Content Finisher (AR-FN6) front alignment motor trouble
    Details Communication establishment error/Fleming/ Parity/Protocol error Detail Front alignment motor operation abnormality
    Cause Motor lock
    Motor rpm abnormality
    Overcurrent to the motor
    Console finisher control PWB trouble
    Cause Defective connection of slave unit PWB connector
    Defective harness between slave unit PWB and ICU PWB
    Slave unit PWB mother board connector pin breakage
    Check and remedy Use DIAG (SIM3-3) to check the motor operation.
    20 Content Finisher (AR-FN6) rear alignment motor trouble
    Check &
    Remedy
    Check connector and harness of slave unit PWB and ICU PWB.
    Check grounding of machine.
    Detail Rear alignment motor operation abnormality
    Cause Motor lock
    Motor rpm abnormality
    Overcurrent to the motor
    Console finisher control PWB trouble
    90 Content PCU communication trouble
    Details
    Cause
    Check &
    Remedy
    Check and remedy Use DIAG (SIM3-3) to check the motor operation.
    F1 00 Content Finisher (AR-FN6) communication trouble 80 Content Finisher (AR-FN6) power abnormality
    Detail Communication cable test error after turning on the power or exiting from DIAG. Communication error with the finisher Detail The 24V power is not supplied to the finisher PWB.
    Cause Improper connection or disconnection of
    connector and harness
    Finisher control PWB trouble
    Power unit trouble
    Cause Improper connection or disconnection of connectors and harness between the machine and the finisher. Finisher control PWB trouble
    Control PWB (PCU) trouble
    Malfunction by noises
    Check and remedy Use DIAG (SIM3-2) to check the sensor.
    87 Content Finisher (AR-FN6) staple rotation motor trouble
    Check and remedy Canceled by turning OFF/ON the power. Check connectors and harness in the communication line.
    Replace the finisher control PWB or PCU
    PWB.
    Detail Front staple rotation motor trouble
    Cause Motor lock
    Motor rpm abnormality
    Overcurrent to the motor
    Finisher control PWB trouble
    08 Content Finisher (AR-FN6) staple shift motor trouble
    Detail Staple motor drive trouble Check and remedy Use DIAG (SIM3-3) to check the motor operation.
    Cause Motor lock
    Motor rpm abnormality
    Overcurrent to the motor
    Finisher control PWB trouble
    F1 00 Content Mail-bin stacker (AR-MS1) communication trouble
    Detail Communication cable test error after turning on the power or exiting from DIAG. Communication error with the Mail-bin stacker.
    Check and remedy Use DIAG (SIM3-3) to check operations of the staple motor.
    10 Content Finisher (AR-FN6) stapler motor trouble
    Detail Stapler motor operation abnormality Cause Improper connection or disconnection of connector and harness between the machine and the Mail-bin stacker.
    Mail-bin stacker control PWB trouble
    Control PWB (PCU) trouble
    Malfunction by noises
    Cause Motor lock
    Motor rpm abnormality
    Overcurrent to the motor
    Console finisher control PWB trouble
    Check and remedy Use DIAG (SIM3-3) to check the motor operation.
    Check and remedy Canceled by turning OFF/ON the power. Check harness and connector in the communication line.
    Replace the Mail-bin stacker PWB or PCU
    PWB.
    11 Content Finisher (AR-FN6) bundle exit motor trouble
    Detail Bundle exit motor operation abnormality
    Cause Motor lock
    Motor rpm abnormality
    Overcurrent to the motor
    Console finisher control PWB trouble
    02 Content Mail-bin stacker (AR-MS1) transport motor abnormality
    Check and remedy Use DIAG (SIM3-3) to check the motor operation. Detail Transport motor trouble
    Cause Motor lock
    Motor rpm abnormality
    Overcurrent to the motor
    Mail-bin stacker control PWB trouble
    15 Content Finisher (AR-FN6) lift motor trouble
    Detail Lift motor operation abnormality
    Cause Motor lock
    Motor rpm abnormality
    Overcurrent to the motor
    Console finisher control PWB trouble
    Check and remedy Use DIAG (SIM3-21) to check the transport motor operation.
    MAIN SUB
    F1 19 Content Console finisher (AR-FN7) front alignment motor trouble
    Detail Front alignment motor operation abnormality
    Cause Motor lock
    Motor rpm abnormality
    Overcurrent to the motor
    Console finisher control PWB trouble
    Check and remedy Use DIAG (SIM3-3) to check the motor operation.
    20 Content Console finisher (AR-FN7) rear alignment motor trouble
    Detail Rear alignment motor operation abnormality
    Cause Motor lock
    Motor rpm abnormality
    Overcurrent to the motor
    Console finisher control PWB trouble
    Check and remedy Use DIAG (SIM3-3) to check the motor operation.
    30 Content Console finisher (AR-FN7) communication trouble
    Detail Communication cable test error after turning on the power or exiting from DIAG. Communication error with the console finisher
    Cause Improper connection or disconnection of connector and harness between the machine and the console finisher.
    Console finisher control PWB trouble
    Control PWB (PCU) trouble
    Malfunction by noises
    Check and remedy Canceled by turning OFF/ON the power. Check connectors and harness in the communication line.
    Replace the console finisher control PWB or PCU PWB.
    31 Content Console finisher (AR-FN7) fold sensor trouble
    Detail Sensor input value abnormality
    Cause Sensor breakage harness breakage
    Console finisher control PWB trouble
    Check and remedy Use DIAG (SIM3-2) to check the sensor operation.
    32 Content Communication trouble between the console finisher (AR-FN7) and the punch unit (AR-PN1).
    Detail Communication err between the console finisher and the punch unit.
    Cause Improper connection or disconnection of connector and harness between the console finisher and the punch unit.
    Console finisher control PWB trouble
    Control PWB (PCU) trouble
    Malfunction by noise
    Check and remedy Canceled by turning OFF/ON the power. Check connectors and harness in the communication line.
    Replace the console finisher control PWB.


    MAIN SUB
    F1 12 Content Mail-bin stacker (AR-MS1) gate trouble
    Detail Gate operation abnormality
    Cause Gate lock
    Mail-bin stacker control PWB trouble
    Check and remedy Use DIAG (SIM3-21) to check the transport gate operation.
    80 Content Mail-bin stacker (AR-MS1) power abnormality
    Detail The 24V power is not supplied to the Mail-bin stacker PWB.
    Cause Improper connection or disconnection of connector and harness
    Mail-bin stacker control PWB trouble
    Power unit (AR-DC1) trouble
    Check and remedy Use DIAG (SIM3-20) to check the sensor operation.
    F1 03 Content Console finisher (AR-FN7) paddle motor trouble
    Detail Paddle motor operation abnormality
    Cause Motor lock
    Motor rpm abnormality
    Overcurrent to the motor
    Console finisher control PWB trouble
    Check and remedy Use DIAG (SIM3-3) to check the motor operation.
    06 Content Console finisher (AR-FN7) slide motor trouble
    Detail Slide motor operation abnormality
    Cause Motor lock
    Motor rpm abnormality
    Overcurrent to the motor
    Console finisher control PWB trouble
    Check and remedy Use DIAG (SIM3-3) to check the motor operation.
    10 Content Console finisher (AR-FN7) stapler motor trouble
    Detail Stapler motor operation abnormality
    Cause Motor lock
    Motor rpm abnormality
    Overcurrent to the motor
    Console finisher control PWB trouble
    Check and remedy Use DIAG (SIM3-3) to check the motor operation.
    11 Content Console finisher (AR-FN7) bundle exit motor trouble
    Detail Bundle exit motor operation abnormality
    Cause Motor lock
    Motor rpm abnormality
    Overcurrent to the motor
    Console finisher control PWB trouble
    Check and remedy Use DIAG (SIM3-3) to check the motor operation.
    15 Content Console finisher (AR-FN7) lift motor trouble
    Detail Lift motor operation abnormality
    Cause Motor lock
    Motor rpm abnormality
    Overcurrent to the motor
    Console finisher control PWB trouble
    Check and remedy Use DIAG (SIM3-3) to check the motor operation.

    MAIN SUB
    F2 00 Content شارپ ar450-ar350 تونر control sensor abnormality
    Detail شارپ ar450-ar350 تونر control sensor output open
    Cause Connector harness trouble Connector disconnection
    Check and remedy Check connection of the شارپ ar450-ar350 تونر control sensor. Check connection of connector and harness to the main PWB.
    Check for disconnection of harness.
    02 Content شارپ ar450-ar350 تونر supply abnormality
    Detail شارپ ar450-ar350 تونر control sensor output value becomes under-شارپ ar450-ar350 تونر too earlier.
    Cause Connector harness trouble
    شارپ ar450-ar350 تونر control sensor trouble
    The شارپ ar450-ar350 تونر cartridge seal is not removed
    Check and remedy Check connection of the connector in the شارپ ar450-ar350 تونر motor section.
    Check connection of connector and harness to the main PWB.
    Check for disconnection of harness.
    شارپ ar450-ar350 تونر control sensor output check DIAG
    ( SIM 25-1)
    Remove the شارپ ar450-ar350 تونر cartridge seal.
    04 Content Improper cartridge (life cycle error, etc.)
    Detail An improper process cartridge is inserted.
    Cause IC chip trouble
    Improper cartridge
    Check and remedy Insert a proper cartridge.
    05 Content CRUM error
    Detail Communication with IC chip cannot be made.
    Cause IC chip trouble
    Improper cartridge
    Check and remedy Insert a proper cartridge.
    39 Content Process thermistor trouble
    Detail Process thermistor open
    Cause Process thermistor trouble
    Process thermistor harness disconnection
    PCU PWB trouble
    Check and remedy Check connection of harness and connector of the process thermistor.
    Check PCU PWB.
    F3 12 Content Machine no. 1 tray lift-up trouble
    Detail PED does not turn ON in the specified time. LUD does not turn ON in the specified time.
    Cause PED/LUD trouble
    No. 1 tray lift-up trouble
    Check connection of harness between the
    PCVU PWB, lift-up unit, and paper feed unit.
    Check and remedy Check PED, LUD, and their harness and connectors.
    Check the lift-up unit.
    22 Content Multi purpose tray lift-up trouble
    Detail MCPED does not turn ON in the specified time.
    MCLUD does not turn ON in the specified time.
    Cause MCPED/MCLUD trouble
    Multi purpose tray lift-up motor trouble
    Harness disconnection f the PCU PWB, the lift-up unit, and the paper feed unit.
    Check and remedy Check MCPED, PCLUD, and their harness and connectors.
    Check the lift-up unit.
    MAIN SUB
    F1 33 Content Console finisher (AR-FN7) punch (AR-PN1) side registration motor trouble
    Detail Punch side registration motor operation abnormality
    Cause Motor lock
    Motor rpm abnormality
    Overcurrent to the motor
    Console finisher control PWB trouble
    Check and remedy Use DIAG (SIM3-3) to check the motor operation.
    34 Content Console finisher (AR-FN7) punch (AR-PN1) motor trouble
    Detail Punch motor operation abnormality
    Cause Motor lock
    Motor rpm abnormality
    Overcurrent to the motor
    Console finisher control PWB trouble
    Check and remedy Use DIAG (SIM3-3) to check the motor operation.
    35 Content Console finisher (AR-FN7) punch (AR-PN1) side registration sensor trouble
    Detail Sensor input value abnormality
    Cause Sensor breakage
    Harness disconnection
    Console finisher control PWB trouble
    Check and remedy Use DIAG (SIM3-2) to check the sensor operation.
    36 Content Console finisher (AR-FN7) punch (AR-PN1) timing sensor trouble
    Detail Sensor input value abnormality
    Cause Sensor breakage
    Harness disconnection
    Console finisher control PWB trouble
    Check and remedy Use DIAG (SIM3-2) to check the sensor operation.
    37 Content Console finisher (AR-FN7) backup RAM trouble
    Detail Backup RAM contents are disturbed.
    Cause Console finisher control PWB trouble Malfunction by noise
    Check and remedy Replace the console finisher control PWB.
    38 Content Console finisher (AR-FN7) punch (AR-PN1) backup RAM trouble
    Detail Punch unit backup RAM contents are disturbed.
    Cause Punch control PWB trouble Malfunction by noise
    Check and remedy Replace the punch control PWB.
    81 Content Console finisher transport motor abnormality
    Detail Transport motor trouble
    Cause Motor lock
    Motor rpm abnormality
    Overcurrent to the motor
    Console finisher control PWB trouble
    Check and remedy Use DIAG (SIM3-3) to check the motor operation.
    MAIN SUB
    H3 00···
    HL1
    (RT H1)
    01···
    HL2
    ( RT H2)
    Content Fusing section high temperature trouble
    Detail The fusing temperature exceeds 242°C. (An input voltage of 0.27V or above is detected.)
    Cause thermistor trouble
    Control PWB trouble
    Fusing section connector disconnection
    AC power trouble
    Check and remedy Use DIAG (SIM5-2) to check the heater lamp Blinking operation.
    If the heater lamp blinks normally:
    Check the thermistor and its harness. Check the thermistor input circuit in the control PWB.
    If the heater lamp keep lighting:
    Check the AC PWB and the lamp control circuit in the control PWB.
    Use DIAG (SIM14) to cancel the trouble
    H4 00···
    HL1
    ( RT H1)
    01···
    HL2
    ( RT H2)
    Content Fusing section low temperature trouble
    Detail •The set temperature is not reached within the specified time (normally 3 min) when warming up or resetting from pre-heating.
    •Under the ready state.
    (An input voltage of 1.21V or below is detected 5 times continuously.)
    Cause thermistor trouble Heater lamp trouble
    Control PWB trouble
    Thermostat trouble
    AC power trouble
    Interlock switch trouble
    Check and remedy Use DIAG (SIM5-2) to check the heater lamp Blinking operation.
    If the heater lamp blinks normally:
    Check the thermistor and its harness. Check the thermistor input circuit in the control PWB.
    If the heater lamp does not light:
    Check for heater lamp disconnection and thermostat disconnection. Check the interlock switch.
    Check the AC PWB and the lamp control circuit in the control PWB.
    Use DIAG (SIM14) to cancel the trouble.
    H5 01 Content 5-time continuous POD1 not-reaching jam detection
    Detail 5-time continuous POD1 not-reaching jam detection
    Cause A fusing section jam is not properly removed.
    ( Jam paper remains. )
    POD1 sensor trouble, or harness disconnection
    Improper installation of fusing unit
    Check and remedy Check jam paper in the fusing section.
    ( winding, etc. )
    Check POD1 sensor harness, and check the fusing unit installation.
    Use DIAG (SIM14) to cancel the trouble.
    L1 00 Content Scanner feed trouble
    Details Scanner feed is not completed within the specified time.
    Cause Scanner unit abnormality
    Scanner wire disconnection
    Check &
    Remedy
    Check scanning with SIM 1-1.
    MAIN SUB
    L3 00 Content Scanner return trouble
    Details Scanner return is not completed within the specified time.
    Cause Scanner unit abnormality Scanner wire disconnection
    Check &
    Remedy
    Check scanning with SIM 1-1.
    L4 01 Content Main motor lock detection
    Detail The motor lock signal is detected for 1.5sec during rotation of the main motor.
    Cause main motor trouble
    Check connection of harness between the PCU PWB and the main motor. Control circuit trouble
    Check and remedy Use DIAG (SIM25-1) to check the main motor operation.
    Check harness and connector between the PCU PWB and the main motor.
    02 Content Drum motor lock detection
    Detail The motor lock signal is detected for 1.5sec during rotation of the drum motor.
    Cause Drum motor trouble
    Improper connection of harness between the PCU PWB and the drum motor.
    Control circuit trouble
    Check and remedy Use DIAG (SIM25-1) to check the drum motor operation.
    Check harness and connector between the PCU PWB and the drum motor.
    L6 10 Content Polygon motor lock detection
    Detail It is judged that the polygon motor lock signal is not outputted.
    Lock signal is checked in the interval of 10sec after starting the polygon motor, and it is judged that the polygon motor does not rotate normally.
    Cause The LSU connector or harness in the LSU is disconnected or broken. Polygon motor trouble
    Check and remedy Use DIAG (SIM61-1) to check the polygon motor operation.
    Check connector and harness connection.
    Replace LSU.
    L8 01 Content No fullwave signal
    Detail Full wave signal is not detected.
    Cause The PCU PWB connector or the power unit harness is disconnected or broken.
    PCU PWB trouble
    Power unit trouble
    Check and remedy Check connection of the harness and connector.
    Replace PCU PWB.
    Replace the power unit.
    02 Content Full wave signal width abnormality
    Detail It is judged as full wave signal frequency abnormality.
    (When the detection cycle is judged as 69Hz or above or 42.5Hz or below)
    Cause The connector or harness of the PCU PWB and the power PWB is disconnected.
    PCU PWB trouble Power unit trouble
    Check and remedy Check connection of the harness and connector.
    Replace the PCU PWB.
    Replace the power unit.
    MAIN SUB
    U6 00
    MAIN SUB
    F6 00 Content Communication trouble (ICU detection) between ICU and FAX
    Details Communication establishment error/Fleming/ Parity/Protocol error
    Cause Slave unit PWB connector disconnection Harness abnormality between slave unit PWB and ICU PWB.
    Slave unit PWB mother board connector pin breakage
    Slave unit ROM abnormality/No ROM/ Reverse insertion of ROM/ROM pin breakable
    Check &
    Remedy
    Check connector harness between slave unit PWB and ICU PWB.
    Check grounding of machine.
    Check slave unit PWB ROM.
    01 Content FAX expansion flash memory abnormality (ICU detection)
    Details Expansion flash memory with SRAM backup data is installed.
    Cause SRAM backup data is detected in expansion flash memory.
    Expansion flash memory in which SRAM data are backed up with SIM 66-19 is installed.
    Check &
    Remedy
    Restore backup data to SRAM with SIM 6620, and clear expansion flash memory with SIM 66-10. If data are unnecessary, clear expansion flash memory with SIM 6610.
    04 Content FAX modem operation abnormality
    Details FAX PWB modem chip operation abnormality
    Cause The boot test pin in the FAX PWB is shorted and normal operation is tried.
    Modem chip operation abnormality in FAX
    PWB
    Check &
    Remedy
    Turn on the power again without shorting the boot test pin in the FAX PWB.
    Replace FAX PWB.
    F7 01 Content FAX board EEPROM read/write error
    Details EEPROM access error (read/write)
    Cause EEPROM trouble
    FAX PWB EEPROM access circuit trouble
    Check &
    Remedy
    Replace FAX PWB.
    H2 00···
    HL1
    (RT H1)
    01···
    HL2
    ( RT
    H2)
    Content thermistor open
    Fusing unit not installed
    Detail Thermistor is open.
    (An input voltage of 2.92V or above is detected.)
    Fusing unit not installed
    Cause Thermistor trouble
    Control PWB trouble
    Fusing section connector disconnection
    AC power trouble
    Fusing unit not installed
    Check and remedy Check harnesses and connectors from the thermistor to the control PWB.
    Use DIAG (SIM14) to clear the self diag display.
    Content
    Desk/LCC communication trouble
    Detail Desk/LCC communication error
    Communication cable test error after turning on the power or exiting DIAG.
    Cause Improper connection or disconnection of
    connector and harness Desk control PWB trouble
    Control PWB (PCU) trouble
    Noise or interference
    Check and remedy Canceled by turning OFF/ON the power. Check connection of the harness and connector in the communication line.
    01 Content Desk/LCC No. 1 tray lift-up trouble
    Detail Desk/LCC No. 1 tray lift-up trouble
    Cause Sensor trouble
    Desk control PWB trouble
    Gear breakage
    Lift-up motor trouble
    Check and remedy Use DIAG (SIM4-2) to check the lift-up sensor detection.
    Use DIAG (SIM4-3) to check the lift-up motor operation.
    02 Content Desk No. 2 tray/LCC1 lift-up trouble
    Detail Desk No. 2 tray/LCC lift-up trouble
    Cause Sensor trouble
    Desk control PWB trouble
    Gear breakage
    Lift-up motor trouble
    Check and remedy Use DIAG (SIM4-2) to check the lift-up sensor detection.
    Use DIAG (SIM4-3) to check the lift-up motor operation.
    03 Content Desk No. 3 tray/LCC2 lift-up trouble
    Detail Desk no. 3 tray lift-up trouble
    Cause Sensor trouble
    Desk control PWB trouble
    Gear breakage
    Lift-up motor trouble
    Check and remedy Use DIAG (SIM4-2) to check the lift-up sensor detection.
    Use DIAG (SIM4-3) to check the lift-up motor operation.
    10 Content Desk/LCC transport motor trouble
    Detail Desk/LCC transport motor operation trouble
    Cause Motor lock
    Motor rpm abnormality
    Overcurrent to the motor
    Desk control PWB trouble
    Check and remedy Use DIAG (SIM4-3) to check the transport motor operation.
    MAIN SUB MAIN SUB
    EE EL Content Auto developer adjustment trouble (Over-شارپ ar450-ar350 تونر) U2 00 Content EEPROM read/write error (Controller)
    Detail EEPROM write error
    Detail The sample data is at 68 or below when auto developer adjustment is performed. Cause EEPROM trouble
    EEPROM is not initialized.
    Controller PWB EEPROM access circuit trouble
    Cause شارپ ar450-ar350 تونر concentration sensor trouble Charging voltage, developing voltage abnormality
    Insufficient شارپ ar450-ar350 تونر concentration
    Developing unit trouble
    PCU PWB trouble
    Check and remedy Check that EEPROM is properly inserted. Save the counter/adjustment values with the DIAG simulation.
    Use DIAG (SIM16) to cancel U2 trouble.
    Replace the Controller PWB.
    Check and remedy Use DIAG (SIM25-2) to perform auto developer adjustment.
    11 Content Counter check sum error (Controller)
    EU Content Auto developer adjustment trouble ( Under-شارپ ar450-ar350 تونر ) Detail Counter data area check sum error
    Cause EEPROM trouble
    Control circuit trouble by noise
    Controller PWB EEPROM access circuit trouble
    Detail The sample data is of 168 or above when auto developer adjustment is performed.
    Cause Insufficient شارپ ar450-ar350 تونر concentration Charging voltage, developing voltage abnormality
    Insufficient شارپ ar450-ar350 تونر concentration
    Developing unit trouble
    PCU PWB trouble
    Check and remedy Check that EEPROM is properly inserted. Save the counter/adjustment values with the DIAG simulation.
    Use DIAG (SIM16) to cancel U2 trouble.
    Replace the Controller PWB.
    Check and remedy Use DIAG (SIM25-2) to perform auto developer adjustment. 12 Content Adjustment value check sum error ( Controller )
    F9 02 Content PRT Centro port check error Detail Adjustment data area check sum error
    Detail Controller Centro port trouble Cause EEPROM trouble
    Control circuit trouble by noise
    Controller PWB EEPROM access circuit trouble
    Cause Centro port trouble Controller PWB trouble
    Check and remedy Replace the Controller PWB.
    Check and remedy Check that EEPROM is properly inserted. Save the counter/adjustment values with the DIAG simulation.
    Use DIAG (SIM16) to cancel U2 trouble.
    Replace the Controller PWB.
    03 Content NIC port check error
    Detail NIC port check error
    Cause NIC port trouble
    NIC PWB trouble
    Controller PWB trouble
    80 Content EEPROM read/write error (Scanner)
    Check and remedy Replace the NIC PWB.
    Replace the Controller PWB.
    Details Scanner EEPROM write error
    Cause EEPROM abnormality
    EEPROM which is not initialized is installed.
    Hang of control circuit due to noises
    Scanner PWB EEPROM access circuit abnormality
    U1 01 Content FAX Battery abnormality
    Detail Backup SRAM battery voltage fall
    Cause Battery life
    Battery circuit abnormality
    Check &
    Remedy
    Check that EEPROM is set properly. Record counter/adjustment values with the simulation to protect the data from being deleted.
    Cancel U2 trouble with SIM 16.
    Replace scanner PWB.
    Check and remedy Check that the battery voltage is about 2.5V or above.
    Check the battery circuit.
    02 Content RTC read abnormality
    (common with FAX, on ICU PWB)
    Details The value read from RTC on ICU PWB is [EE]h (abnormal). 81 Content Memory check sum error (Scanner)
    Details Scanner memory check sum error
    Cause RTC circuit abnormality
    Battery voltage fall
    Battery circuit abnormality
    Cause EEPROM trouble
    Control circuit freeze by noises
    Scanner PWB EEPROM access circuit trouble
    Check &
    Remedy
    Set the time again with key operation, and check that time advances properly.
    Check RTC circuit.
    Check that battery voltage is about 2.5V or above.
    Check battery circuit.
    Check &
    Remedy
    Check that EEPROM is set properly. Record counter/adjustment values with the simulation to protect the data from being deleted.
    Cancel U2 trouble with SIM 16.
    Replace scanner PWB.
    Error code
    Content of error
    CE-01
    The print server card (AR-NC5J) is broken down or is not installed.
    CE-02
    The specified mail server or FTP server is not found.
    CE-03
    Communication with the specified server is interrupted during image transmission.
    CE-04
    The account name or the password for the FTP server is invalid.
    CE-05
    The directory of the FTP server is invalid.
    CE-00
    A communication error other than the above is generated, such as NIC cable disconnection

    1. 3. Network communication error

    MAIN SUB
    U2 90 Content EEPROM read/write error (PCU)
    Detail PCU EEPROM write error
    Cause EEPROM trouble
    EEPROM is not initialized.
    Hang of control circuit due to noises
    PCU PWB EEPROM access circuit trouble
    Check and remedy Check that EEPROM is properly inserted. Save the counter/adjustment values with the DIAG simulation.
    Use DIAG (SIM16) to cancel U2 trouble.
    Replace the Controller PWB.
    91 Content Memory check sum error (PCU)
    Detail PCU memory check sum error
    Cause EEPROM trouble
    EEPROM is not initialized.
    PCU PWB EEPROM access circuit trouble Uninitialized EEPROM installed.
    Check and remedy Check that EEPROM is properly inserted. Save the counter/adjustment values with the DIAG simulation.
    Use DIAG (SIM16) to cancel U2 trouble.
    Replace the Controller PWB.
    U7 00 Content RIC communication trouble
    Detail RIC communication trouble
    Communication cable test error after turning on the power or exiting DIAG.
    Cause Disconnection of connector and harness
    RTC control PWB trouble
    Control PWB (Controller) trouble
    Noise or interference
    Check and remedy Canceled by turning OFF/ON the power. Check connector and harness in the communication line.
    PF 00 Content RIC copy inhibit signal is received.
    Detail Copy inhibit command from RIM (host) is received.
    Cause Judged by the host.
    Check and remedy Inform to the host.
    •Error code table

    ویرایش توسط @sorena : 21st May 2017 در ساعت 18:10
    در تصاویر حکاکی شده بر سنگ های تخت جمشید،
    هیچکس عصبانی نیست!
    هیچکس سوار اسب نیست!
    هیچکس را در حال تعظیم نمیبینید!
    در بین این صدها پیکر تراشیده حتی یک تصویر برهنه وجود ندارد!
    اینها اصالت ما هستند: مهربانی، خوشرویی، قدرت، احترام، ادب، نجابت


اطلاعات موضوع

کاربرانی که در حال مشاهده این موضوع هستند

در حال حاضر 1 کاربر در حال مشاهده این موضوع است. (0 کاربران و 1 مهمان ها)

کلمات کلیدی این موضوع

مجوز های ارسال و ویرایش

  • شما نمیتوانید موضوع جدیدی ارسال کنید
  • شما امکان ارسال پاسخ را ندارید
  • شما نمیتوانید فایل پیوست کنید.
  • شما نمیتوانید پست های خود را ویرایش کنید
  •  


Copyright ©2000 - 2013, Jelsoft Enterprises Ltd کیــــــــــان ستـــــــــــ ...® اولین و بزرگترین سایت فوق تخصصی الکترونیک در ایران



Cultural Forum | Study at Malaysian University