abasfar (21st April 2015),alireza3135 (10th November 2011),ASHKAN-NO (6th August 2012),kamalsr1353 (22nd October 2017),KAZEMLU (12th November 2010),m2007_mail (6th August 2012),mehdi-2 (31st March 2020),mohabat007 (20th March 2010),mohammad amin 69 (30th May 2016),pal-electronic (6th August 2012),razbagha16 (26th July 2011),SOBHAN86 (14th October 2013),Tezar (6th August 2012),محمد دهقان (1st June 2010),ziregue (18th July 2013),جبرائل خدایی (15th February 2018),حسن محمدي (2nd March 2011),داوودی فر (19th May 2014),رامین فرهادی (15th October 2010),شهریار (14th June 2011),شعبانیان (21st November 2011),غدیر (6th August 2012)
مشخصات ومحدوده زیر برای اکثر ال سی دی هاست
شاسی :
LP91A/B/C/D chassis
1. Application Range
This specification sheet is applied to all of the LCD TV,
LP91A/B/C/D chassis.
2. Specification
1) Because this is not a hot chassis, it is not necessary to use
an isolation transformer. However, the use of isolation
transformer will help protect test instrument.
2) Adjustment must be done in the correct order.
3) The adjustment must be performed in the circumstance of
25 ±5 °C of temperature and 65±10% of relative humidity if
there is no specific designation.
4) The input voltage of the receiver must keep 100~220V,
50/60Hz.
5) Before adjustment, execute Heat-Run for 5 minutes at RF
no signal.
3. Adjustment items
3.1. PCB assembly adjustment items
(1) Download the MSTAR main software
(IC800, Mstar ISP Utility)
1) Using D/L Jig
2) Using USB Memory Stick.
(2) ADC Calibration – RGB / Component
(3) Input Tool-Option/Area option.
(4) Check SW Version.
4. PCB assembly adjustment method
4.1. Mstar Main S/W program download
4.1.1. Using D/L Jig
(1) Preliminary steps
1) Connect the download jig to D-sub(RGB) jack
(2) Download steps
1) Execute ‘ISP Tool’ program, the main window(Mstar ISP
utility Vx.x.x) will be opened
2) Click the “Connect” button and confirm “Dialog Box”
3) Click the “Config.” button and Change speed I2C Speed
setting : 350Khz~400Khz
4) Read and write bin file.
Click “(1)Read” tab, and then load download
file(***X.bin) by clicking “Read”.
5) Click “(2)Auto” tab and set as below
6) Click “(3)Run”.
7) After downloading, you can see the “(4)Pass” message.
4.1.2. Using the Memory Stick
* USB download : Service Mode
1) Insert the USB memory stick to the ISB port.
2) Automatically detect the SW Version.
-> S/W download process is executed automatically.
3) Show the message “Copy the file from the Memory”
4) After Finished the Download, Automatically DC Off -> On
4.2. Adjust tool/area option.
Adjust tool/area option refer to the BOM.
4.3. Adjust tool/area option.
Adjust tool/area option refer to the BOM.
4.4. EDID D/L method
Recommend that don’t connect HDMI and RGB(D-SUB) cable
when downloading the EDID.
If not possible, recommend that connect the MSPG equipment.
There are two methods of downloading the edid data
4.4.1. 1st Method
EDID datas are automatically downloaded when adjusting the
Tool Option2.
Automatically downloaded when pushing the enter key after
adjusting the tool option2.
It takes about 2seconds.
4.4.2. 2nd Method
* Caution :
Must be checked that the tool option is right or not.
If tool option is wrong, hdmi edid data could not be
downloaded well.
1) Press the ADJ key
2) Move to the EDID D/L and Press the right direction key(G)
3) Press the right direction key(G) at Start.
4) After about a few seconds, appear “OK”, then compele.
Caution
Don’t connect HDMI and RGB(D-SUB) cable when
downloading the EDID.
If the cables are connected, Downloading of edid could be
failed.
abasfar (21st April 2015),ASHKAN-NO (6th August 2012),benyamin70 (8th October 2014),m2007_mail (6th August 2012),MAHMOOD1 (16th September 2013),mehdi-2 (31st March 2020),mohabat007 (20th March 2010),mohammad amin 69 (30th May 2016),pal-electronic (6th August 2012),razbagha16 (25th April 2011),SOBHAN86 (14th October 2013),Tezar (6th August 2012),محمد دهقان (1st June 2010),محسن اسدی (18th February 2010),ziregue (18th July 2013),حسن محمدي (2nd March 2011),داوودی فر (18th May 2014),رامین فرهادی (15th October 2010),شهریار (14th June 2011),شعبانیان (21st November 2011),غدیر (6th August 2012)
در حال حاضر 1 کاربر در حال مشاهده این موضوع است. (0 کاربران و 1 مهمان ها)